Feeling handy

Got my hands dirty a bit ago.

When I got my second car, the first sat outside for months after the battery died. I had ignored it too long, and actually began looking up the things that could go wrong with it. Bad idea. I picked a time to give it some attention, and ascertain its status.

I turned the key to just before starting, and checked the fuel level... Full. Damnit. I had hoped I could add half a tank of gas to mix up the possibly settled old gas, but no dice. I wanted to try a start without draining the tank, so I rocked the car as much as I could in the hopes of getting some mixing action in the gas tank. The tires were very low, but still had a seal, so they would work to make it down the street to the gas station and air compressor. I checked the hoses again for any weathering damage, and tried for a start... VROOOM! Just as strong as when I left it. Go Dodge.

After letting it run for a bit, I slowly drove it to the gas station, and saw a hastily made sign taped to the air compressor, "Broken." A little bit further was the Sears I was going to buy the battery from, It was only half a mile, and one light, so I made a go at it. (like I had any other choice)

As I waited to make a left turn at the light, I noticed the dashboard lights flickering as they got uneven energy without the help of the battery, and realized that given my position, and my intended destination, the car dying at this moment would mean me pushing the car across a large busy intersection, ~500 yards down the street, and up a notable slope into the parking lot. I pushed the thought from my mind as I idled the car a little high until the light changed.

I parked the car on an incline, and bought the new battery. I popped the hood, pulled the connections, and pulled on the battery. It didn't budge. I checked around the battery, and it looked clear, but it wouldn't move. Could it be glued by the factory or something? That wouldn't make sense. I noticed a screw that held a small piece of metal at the base of the battery, but it was at such an angle that it didn't look like it was holding the battery at all. So I thought for a bit, and decided that bolt had to go, mostly because it was my best guess. But all I had were some vicegrips, and the engine jungle of wires and hoses made it impossible to get at it without a ratchet and an extender. Well, I've needed a ratchet set for a while.

I walked from the sears auto center to the main store, and bought a ratchet set and extender set, and was able to replace the battery with no problem. The screw held down a piece of metal that put pressure on a flair at the bottom of the battery body I hadn't noticed before. Pretty solid hold for such a simple system. They were kind enough to let me fill up my tires there, so I was off to the oil change spot where they changed the oil, topped off fluids, and cleaned a layer of crud off the windows, and cobwebs out of the interior. It almost looked normal again.

I am a dangerous man.

Feeling handy for the rest of the day, I lightened the trigger on my 91/59 by placing two short pieces of a plastic straw under the sear/spring/thingy on either side of the screw that holds it there. This makes the trigger just ok, but it'll need some more work before it gets to the level of the M39. While I was at it, I floated the barrel by applying layers of painting tape to the stock where the base of the barrel rests. The barrel now sits loosely within the stock and barrel bands. I have yet to shoot it though, so I'll have no real gauge for improvement. Whatever... HANDY!!!

I then thought for a bit how to repair my paintball pants, which had a hole worn through the kneepad clear to the lining. It's very painful when you slide into a bunker into a position on your knees and stop your knee right on a rock without the benefit of padding. I wandered the house searching for something I could use, and actually found something! The old leather couch had been destroyed and disposed of, but we kept some of the cushions for Ava to chew on and play with. I cut a section out of the leather, and cut a cube out of the first layer of foam. With a bit of fitting, the cube matched the hole in the existing knee padding perfectly, and I somehow managed to get the whole thing under the sewing machine to attach the leather patch and foam cube to the pants securely. I didn't want to cut a hole in the liner for fear of catching it when putting the pants on and tearing it, so I just sewed through the liner too. The results were quite good. The stitching was a little uneven, but secure. I used some "anything" glue to touch up the edges so the patch wouldn't catch and tear off, but the glue was so good I wished I had skipped the sewing and used the glue only, which would have left the liner loose. Oh well, it still works great.

It's not like I built a house or anything, but baby steps for now.

I would totally build a house.

Three rifle bag

Whenever I have to bring more than one long gun anywhere, I have to make multiple trips from the apartment to the car. Worse; since I don't have multiple cases/gun socks, I wind up putting a gun in a gun sock, carrying it to my trunk, removing the gun sock, then putting it on the next long gun I need to carry to my car.

On trips to the desert, where I'm inclined to bring multiple guns, this can be cumbersome.

I couldn't find any place that sold rifle cases that held multiple long guns without being huge, so I decided to make something to carry multiple long guns at the same time discreetly, and without fear of dropping them all.

I had the heavy canvas, so I just went at it. I'm rather pleased with the results


I only did three sections because I wanted them wide enough for my widest gun (AR-15, 10"), but if you have a lot of thin guns, you could probably make it to four sections easily. Though I wonder if at that point the weight will become too much a factor.

The measurements are 45"x30". The sections are 10 inches wide to accommodate an AR. You can futz on the rest of the sections, but be sure that at least one is 10 inches, or enough to fit your AR. 10 inches is a little snug for an AR, so measure twice, sew once.



Once you have them in the pockets, fold them up like a "Z" so they're kind of stacked.


It would behoove you to ensure that your flattest gun goes on the side you intend to sling over your back. AK charging handles in the back hurt.

Since I was still working out some kinks in the shoulder strap and retention design, I just went for the paracord.

This is one length with a taughtline hitch and a bowline hitch, and another length with two bowline hitches. It will be made for use with an existing shoulder strap. I picked a comfy one from my bailout bag. (heh, "bailout." wonder if it's full of billions of dollars)

Bunch up the open ends of the stacked pouches, and slip the taughtline hitch over the end.

The taughtline hitch is meant not to move. Failing to keep this loop tight could result in the ends of the pouches slipping through, and everything falling to the ground.

To take up some of the extra slack, wrap the bowline hitch around once, and run it through itself. This will shorten the distance between your shoulder strap and the top of your three rifle bag.


Tightness at the bottom is less important since it need only make a second contact point.

I've just run one bowline hitch through the other.


Using the loops you've created, attach your favorite shoulder strap, and sling that sucker over your shoulder. It'll probably hang low. It's not very comfortable, but it works great for the short trip to the car.

Also, it bundles up quite nicely.

The SKS slimline clip carrier

After purchasing my new sewing machine Fully-Automatic Tactical Thread Delivery Device, I wasted no time assembling something I'd been thinking about for a while.

A few hours later, I had a prototype.

I keep my SKS ready as a trunk gun, and had difficulty thinking of a way to keep some stripper clips easily available for carry should I ever to grab it. Kind of a grab and go clip carrier.







I'm thinking about adding something like a belt clip. The tight fit is alright for holding the stripper clips in place with light jostling, but anything more and the clips fly free. I'm trying to think of a simple retention device for them that doesn't get in the way or add too much bulk.

Next project is the three level messenger bag. A messenger bag designed for carrying a pistol at three different levels of concealment/readiness. At high readiness, the pistol would be exposed and ready for draw, and an outer pocket would expand into rifle mag pockets and a dump pouch. Also, it would clean your room and walk your dog. I will entertain suggestions on this project.